Symetrix xIN 12 Input Expander
Symetrix xIN 12 Input Expander
Symetrix xIN 12 Input Expander

Symetrix xIN 12 Input Expander

Call For Price

Symetrix xIN 12 Input Expander For Use With Symterix Dante Enabled Devices
  • Designed for Use with Symetrix Dante-enabled DSPs
  • Software Setup Using Composer
  • Low Cost Way to Increase System Analog I/O Capacity
  • Ultra Low Latency – No Audible Delays
  • Top of the Line Specifications

Architect and Engineer Specifications: xIn 12.

The device shall provide twelve analog mic/line inputs that are adjustable from line to mic level with coarse gain and phantom power. Levels and phantom power shall be controllable via online connection with software only. Audio connections shall be accessed via rear panel 3.81 mm terminal block connectors.

Network audio expansion shall be provided by the Dante protocol. Primary and Secondary Dante network audio connections shall be provided for redundant network implementation. Connectors shall be gigabit RJ45 utilizing CAT6 cable.

A designer software application shall be provided that operates on a Windows computer, with network interface installed, running Windows® XP or higher operating system. Computer connection for configuration shall be via a hosting DSP unit’s rear panel Ethernet connector that communicates with the device via Dante.

The front panel shall include input signal level indicators as well as indicators for POWER and DANTE (PRIMARY and SECONDARY).

Audio conversion shall be 24-bit, 48 kHz and the dynamic range shall not be lower than 116 dB, A-weighted with a maximum input level of +23 dBu.

The device shall have an IEC power input socket for 120-240 VAC. The device shall meet UL/CSA and CE safety requirements and comply with CE and FCC Part 15 emissions limits. The device shall be RoHS compliant. The chassis shall be constructed of cold rolled steel and moulded plastic, and mount into a standard 19” 1U EIA rack. The device shall be a Symetrix xIn 12.

General Specifications

Sampling rate48 kHz, ± 100 ppm.
Frequency response (A/D)20 Hz – 20 kHz, ± 0.5 dB.
Channel separation (A/D)> 111 dB @ 1 kHz, +24 dBu.
Dante cableStandard CAT6, maximum device to device length = 100 meters.
Connectors3.81 mm terminal blocks.
Number of inputsTwelve (12) switchable balanced mic or line level.
Nominal input level+4 dBu with 20 dB of headroom.
Maximum input level+23 dBu.
Mic pre-amp gain0, 11.8, 24, 44 or 54 dB switchable.
Mic pre-amp EIN< -127 dB with 150 Ohm source impedance.
Input impedance8k Ohms balanced, 4k Ohms unbalanced.
Phantom power (per input)+48 VDC @ 10 mA maximum.
Dynamic range> 116 dB, A-weighted.
THD + Noise< -100 dB, unweighted; 1 kHz @ +22 dBu with 0 dB gain.
Latency0.28 mS.

Mechanical Data

Space Required1U (WDH: 18.91 in x 9.5 in x 1.72 in / 48.02 cm x 24.13 cm x 4.37 cm). Depth does not include connector allowance. Allow at least 3 inch additional clearance for rear panel connections. Additional depth may be required depending upon your specific wiring and connections.
Electrical100-240 VAC, 50/60 Hz, 25 Watts maximum universal input. No line voltage switching required.
VentilationMaximum recommended ambient operating temperature is 30 C / 86 F. Ensure that the left and right equipment sides are unobstructed (5.08 cm, 2 in. minimum clearance). The ventilation should not be impeded by covering the ventilation openings with items such as newspapers, tablecloths, curtains, etc.
Shipping Weight12 lbs. (5.4 kg).
Certifications or ComplianceUL 60065, cUL 60065, IEC 60065, EN 55103-1, EN 55103-2, FCC Part 15, RoHS.

Additional information

Weight5.4 kg

You may also like…