Symetrix xOut 4 Output Expander

Symetrix xOut 4 Output Expander

Call For Price

Symetrix xOut 4 Output Expander For Use With Symetrix Dante Enabled Devices.
  • Designed for Use with Symetrix Dante-enabled DSPs
  • Software Setup Using Composer
  • Low Cost Way to Increase System Analog I/O Capacity
  • Ultra Low Latency – No Audible Delays
  • Top of the Line Specifications

Architect and Engineer Specifications: xOut 4.

The half rack device shall provide four analog line outputs. Levels shall be controllable via DSP modules in software. Audio connections shall be accessed via rear panel 3.5 mm Phoenix® connectors.

Network audio expansion shall be provided by the Dante protocol. The connector shall be 100 Base-T RJ45 utilizing CAT6 cable.

A designer software application shall be provided that operates on a Windows computer, with network interface installed, running Windows® 7 or higher operating system. Computer connection for configuration shall be via a hosting DSP unit’s rear panel Ethernet connector that communicates with the devices via Dante.

The front panel shall include indicators for POWER, ETHERNET, and DANTE.

Audio conversion shall be 24-bit, 48 kHz and the dynamic range shall not be lower than 115 dB, A-weighted with a maximum output level of +24 dBu.

The device shall be powered over Ethernet (PoE) by an included 802.3af Class 0 PoE injector. The device shall meet UL/CSA and CE safety requirements and comply with CE and FCC Part 15 emissions limits. The device shall be RoHS compliant. The chassis shall be constructed of cold rolled steel, and may be surface mounted or mount into a standard 19” 1U EIA rack using available mounting kits. The device shall be a Symetrix xOut 4.

Analog Outputs

Frequency Response20 Hz – 20 kHz, ± 0.5 dB.
Channel Separation> 111 dB @ 1 kHz, +24 dBu.
Connectors3.5 mm Phoenix® connectors.
Number of outputsFour (4) balanced line level.
Nominal output level+4 dBu with 20 dB of headroom.
Maximum output level+24 dBu (+22.8 dBu into a 2k Ohm minimum load).
Output impedance300 Ohms balanced, 150 Ohms unbalanced.
Dynamic range> 118 dB, A-weighted.
THD + Noise< -105 dB, unweighted; 1 kHz @ +22 dBu with 0 dB gain.
Latency0.60 mS.

System

Sampling Rate48 kHz, ± 100 ppm.
Dante CableStandard CAT6, maximum device-to-device length = 100 meters.

Mechanical Specifications

Space RequiredHalf rack unit (WDH: 20.83 cm x 22.86 cm x 4.37 cm / 8.2 in. x 9 in. x 1.72 in.) Depth does not include connector allowance. Allow at least 3 inches additional clearance for rear panel connections. Additional depth may be required depending upon your specific wiring and connections.
ElectricalPoE IEEE 802.3af Class 0, 10 Watts maximum. No line voltage switching required (100-250 VAC, 50-60 Hz).
VentilationMaximum recommended ambient operating temperature is 30 C / 86 F. Ensure that the left and right equipment sides are unobstructed (5.08 cm, 2 in minimum clearance). The ventilation should not be impeded by covering the ventilation openings with items such as newspapers, tablecloths, curtains, etc.
Certifications or ComplianceUL 60065, cUL 60065, IEC 60065, FCC 15.109:2015, FCC 15.109(g):2015, FCC 15.107:2015, (CISPR 32), EN 55032:2012, EN 55103-2:2009, EN 61000-3-3:2013, EN 61000-3-2:2006, ICES-003:2012, RoHS.
Shipping Weight4.4 lbs. (2.0 kg)

Additional information

Weight2 kg

You may also like…